Ford Taurus Service Manual: General Procedures

Safety Belt Cleaning

  1.  WARNING: Do not bleach or re-dye the safety belt webbing, as the webbing may weaken. Failure to follow this instruction may increase the risk of serious personal injury or death in a crash.

    Clean the safety belt webbing only with a mild soap solution recommended for cleaning upholstery or carpets. Follow the instructions provided with the soap.

Safety Belt Maintenance

 WARNING: All safety belt components must be inspected and corrected as part of any collision repair. Inspect all safety belt components as prescribed by Safety Belt Inspection and Repair After a Collision found in Section 501-20A General Procedures of this manual. Failure to follow this instruction may result in incorrect operation of the safety belt system and increase the risk of serious personal injury or death in a crash.

  1. The safety belt assemblies should be periodically inspected to make sure that they have not become damaged and that they remain in correct operating condition, particularly if they have been subjected to severe stress.
  1. Before installing the new safety belt assembly, the safety belt retaining areas must be inspected for damage and distortion. If the retaining points are damaged and distorted, the sheet metal must be reworked back to its original shape and structural integrity.
  1. Install the new safety belt(s) using the appropriate instructions. Carry out the appropriate Functional Test Procedure. For additional information, refer to the appropriate Functional Test procedure in Safety Belt System in this section.

Safety Belt Inspection and Repair After a Collision

  1. After a crash, the following safety belt components and attaching hardware must be inspected and tested to verify correct function at all seating positions. Components that do not operate correctly or pass all Functional Tests located in Component Tests of Safety Belt System must be replaced with new components.
    • Retractors
    • Buckles
    • Safety belt shoulder belt height adjusters (if equipped)
    • Front safety belt buckle support assemblies (slide bar) (if equipped)
    • Automatic Locking Retractor (ALR) feature for child safety seats (passenger seating positions only)
    • Child safety seat tether bracket assemblies
    • Lower anchors and tethers for children
    • Belt Tension Sensor (BTS) (if equipped)
    • Inflatable safety belt systems (if equipped)
  1. Before installing a new safety belt assembly, inspect all safety belt attaching points for damage and distortion. If the attaching points are damaged or distorted, the sheet metal must be restored to its original shape and structural integrity.
  1. Install new safety belt(s) at any seating position(s) where safety belt deployment has occurred and the safety belt(s) were used.

Safety Belt Tongue Rotated on Belt

  1. Fold the safety belt as indicated.

    Ford Taurus. Body

  1. Pull the safety belt tongue over the fold in the safety belt.

    Ford Taurus. Body

Safety Belt Twisted at the Safety Belt Guide

NOTE: These procedures apply to both wire-formed and stamped D-ring designs.

  1. If necessary, for access, remove the appropriate interior trim panel. Refer to Section 501-05.
  1. Grasp the belt webbing at the shoulder belt guide (D-ring).
  1. Rotate and fold the belt webbing over itself to remove the twist.
  1. Feed the folded portion of the belt through the safety belt guide (D-ring).

    Ford Taurus. Body

  1. When completed, the safety belt should look like the illustration.

    Ford Taurus. Body

    Diagnosis and Testing
    Safety Belt System Principles of Operation  WARNING: All safety belt components must be inspected and corrected as part of any collision repair. Inspect all safety belt components as prescribed ...

    Removal and Installation
    Safety Belt Anchor and Pretensioner Special Tool(s) Removal and Installation  WARNING: All safety belt components must be inspected and corrected as part of any collision repair. Inspect all s ...

    Other materials:

    General Procedures
    Headlamp Adjustment Special Tool(s) Headlamp Adjustment Screw Location Headlamp Aiming The headlamp aiming procedure depends on what type of beam pattern the headlamp is equipped with. Vehicles may come equipped with visually optically aligned left (VOL) or visually optically aligned right ( ...

    Power seats
    WARNING: Never adjust the driver’s seat or seat back when the vehicle is moving. WARNING: Before returning the seat back to its original position, make sure that cargo or any objects are not trapped behind the seat back. Note: On vehicles with memory seats, to prevent damage to the seat, t ...

    Disassembly and Assembly of Subassemblies
    Transaxle Case Special Tool(s) Exploded View Disassembly Special Tool(s): Remover/Installer, Front Wheel Hub 204-069 (T81P-1104-C), Transfer Gear Bearing Race Remover 307-577 Punch a hole in the fluid dam. Center punch. General Equipment: Dent Puller Special Tool(s): Dif ...